Press Settings Reference
Fauxbroidery Transfers Press Settings for CVC Blend (60/40)
For Fauxbroidery Transfers on CVC Blend (60/40): press at 300-315F for 12-15 seconds with medium-firm pressure, warm peel. The dimensional puff layer in fauxbroidery transfers activates and expands within this temperature range on CVC Blend (60/40). Standard medium pressure is appropriate for optimal puff definition on CVC Blend (60/40).
Quick Reference Settings
| Setting | Recommended Value |
|---|---|
| Temperature | 300-315F (149-157C) |
| Press Time | 12-15 seconds |
| Pressure | Medium-Firm |
| Peel Method | Warm Peel (5-15 seconds) |
| Pre-Press Temp | 300-315F, 3-5 sec |
| Finish Press | 300-310F, 5-8 sec |
| Dye Migration Risk | moderate |
Weight note: CVC blends are typically midweight (4.3-5.5 oz). Standard settings work across the range.
About CVC Blend (60/40)
60% Cotton / 40% Polyester (Chief Value Cotton)
Common examples: Next Level 6210, Bella+Canvas 3001CVC, LAT 6901, Tultex 241
Step-by-Step Pressing Process
- 1
Pre-press the fabric
Set your heat press to 300-315F. Press the substrate for 3-5 seconds without the transfer to remove moisture and flatten wrinkles. Standard pre-press for moisture removal.
- 2
Position the transfer
Center the Fauxbroidery Transfers on the fabric in the correct placement location. For apparel, use a heat-resistant tape or alignment ruler to verify placement before pressing.
- 3
Apply heat and pressure
Press at 300-315F for 12-15 seconds with medium-firm pressure. The puff layer will expand during pressing. Do not open the press early.
- 4
Peel the carrier film (warm peel)
Wait 5-15 seconds after pressing, then test a corner. When the carrier film releases smoothly without resistance, peel in one steady motion. Do not peel while the film is still hot or completely cold.
- 5
Finish press
Place a Teflon sheet or parchment paper over the peeled design. Re-press at 300-310F for 5-8 seconds with medium pressure. Use Teflon sheet. Standard finishing press.
Pre-Press Details
Standard pre-press for moisture removal.
Finish Press Details
Use Teflon sheet. Standard finishing press.
Fauxbroidery-Specific Notes for CVC Blend (60/40)
Fauxbroidery transfers include a raised puff layer that expands during pressing to replicate the dimensional look of embroidery. On CVC Blend (60/40), press at 300-315F. Standard pressure allows the puff layer to activate fully while maintaining even substrate contact. The puff texture is most visible on smooth, flat fabric surfaces.
Common Pitfalls on CVC Blend (60/40)
- CVC blends still contain 40% polyester — do not exceed 315F on dark colors.
- Higher cotton content gives more heat tolerance than 50/50, but still requires caution.
Pro Tips for CVC Blend (60/40)
- CVC blends offer the best balance of soft hand-feel and DTF compatibility.
- The higher cotton percentage allows slightly higher temps than 50/50, giving better adhesion.
- 300-310F for 12-15 seconds is the sweet spot for most CVC blanks.
Frequently Asked Questions
What temperature should I use for Fauxbroidery on CVC Blend (60/40)?
Press at 300-315F (149-157C). Start at the lower end of the range and increase only if adhesion test fails. CVC blends are typically midweight (4.3-5.5 oz). Standard settings work across the range.
How long should I press Fauxbroidery transfers on CVC Blend (60/40)?
Press for 12-15 seconds at medium-firm pressure. Heavier fabric weights need the upper end of the time range. Never increase temperature to compensate for thickness — always add time instead.
Hot peel or cold peel for Fauxbroidery on CVC Blend (60/40)?
Use warm peel for CVC Blend (60/40). Wait 5-15 seconds after pressing, test a corner, then peel smoothly when the film releases without resistance. This method gives the best adhesion results on this fabric type.
What are the most common mistakes when pressing Fauxbroidery on CVC Blend (60/40)?
CVC blends still contain 40% polyester — do not exceed 315F on dark colors. Higher cotton content gives more heat tolerance than 50/50, but still requires caution. Tip: CVC blends offer the best balance of soft hand-feel and DTF compatibility.
Wondering if Fauxbroidery is compatible with CVC Blend (60/40)? See the full compatibility analysis for Fauxbroidery Transfers on CVC Blend (60/40)
Order Fauxbroidery Transfers from Long Island DTF Printing
Wholesale fauxbroidery transfers starting at $0.06/sq inch. 24-hour standard turnaround. No minimums on most products.