Press Settings Reference
Fauxbroidery Transfers Press Settings for Performance Polyester
For Fauxbroidery Transfers on Performance Polyester: press at 270-285F for 10-12 seconds with medium pressure, cold peel. The dimensional puff layer in fauxbroidery transfers activates and expands within this temperature range on Performance Polyester. Standard medium pressure is appropriate for optimal puff definition on Performance Polyester.
Quick Reference Settings
| Setting | Recommended Value |
|---|---|
| Temperature | 270-285F (132-140C) |
| Press Time | 10-12 seconds |
| Pressure | Medium |
| Peel Method | Cold Peel (30-90 seconds) |
| Pre-Press Temp | 270-280F, 5-7 sec |
| Finish Press | 270-280F, 5-8 sec |
| Dye Migration Risk | very high |
About Performance Polyester
100% Polyester (moisture-wicking / dri-fit construction)
Common examples: Nike Dri-FIT, Under Armour Tech, Adidas Climalite, Sport-Tek PosiCharge ST350
Step-by-Step Pressing Process
- 1
Pre-press the fabric
Set your heat press to 270-280F. Press the substrate for 5-7 seconds without the transfer to remove moisture and flatten wrinkles. CRITICAL for performance poly. These fabrics trap moisture invisibly. Pre-press for 5-7 seconds — you will see steam escape. This step is non-negotiable for adhesion.
- 2
Position the transfer
Center the Fauxbroidery Transfers on the fabric in the correct placement location. For apparel, use a heat-resistant tape or alignment ruler to verify placement before pressing.
- 3
Apply heat and pressure
Press at 270-285F for 10-12 seconds with medium pressure. The puff layer will expand during pressing. Do not open the press early.
- 4
Peel the carrier film (cold peel)
Wait 30-90 seconds for the transfer to cool completely to room temperature before peeling. Peeling while still warm on a cold-peel film will lift the design. When in doubt, wait longer.
- 5
Finish press
Place a Teflon sheet or parchment paper over the peeled design. Re-press at 270-280F for 5-8 seconds with medium pressure. Use Teflon sheet. Do not exceed initial press temperature. Keep finishing brief.
Pre-Press Details
CRITICAL for performance poly. These fabrics trap moisture invisibly. Pre-press for 5-7 seconds — you will see steam escape. This step is non-negotiable for adhesion.
Finish Press Details
Use Teflon sheet. Do not exceed initial press temperature. Keep finishing brief.
Fauxbroidery-Specific Notes for Performance Polyester
Fauxbroidery transfers include a raised puff layer that expands during pressing to replicate the dimensional look of embroidery. On Performance Polyester, press at 270-285F. Standard pressure allows the puff layer to activate fully while maintaining even substrate contact. The puff texture is most visible on smooth, flat fabric surfaces.
Common Pitfalls on Performance Polyester
- HIGHEST dye migration risk of any fabric type. Performance poly dyes are especially reactive.
- Never exceed 285F. Even 290F can trigger migration on dark performance jerseys.
- The mesh/wicking construction means heat transfers differently through the fabric. Monitor closely.
- Sublimated performance garments have extreme dye migration risk — the sublimation dyes re-activate at DTF press temperatures.
- Do NOT stack hot performance garments. Lay flat, spaced apart, to cool completely.
Pro Tips for Performance Polyester
- Start at 270F for 10 seconds. Only increase if adhesion test fails.
- Cold peel is mandatory. Wait 60+ seconds for full cooling.
- Test every brand/style separately — dye formulations vary dramatically between manufacturers.
- The 5-7 second pre-press for moisture removal is the single most important step for performance poly.
- If dye migration occurs despite low temp, try using a barrier sheet between the garment and lower platen.
Frequently Asked Questions
What temperature should I use for Fauxbroidery on Performance Polyester?
Press at 270-285F (132-140C). Start at the lower end of the range and increase only if adhesion test fails.
How long should I press Fauxbroidery transfers on Performance Polyester?
Press for 10-12 seconds at medium pressure.
Hot peel or cold peel for Fauxbroidery on Performance Polyester?
Cold peel is required for Performance Polyester. Wait at least 30-60 seconds after pressing before peeling the carrier film. On darker colors, wait 90+ seconds.
How do I prevent dye migration when pressing Fauxbroidery Transfers on Performance Polyester?
Dye migration risk for Performance Polyester is very-high. HIGHEST dye migration risk of any fabric type. Performance poly dyes are especially reactive.. The most effective countermeasure is staying at the lowest effective temperature and using cold peel with a full cooling period before stacking.
What are the most common mistakes when pressing Fauxbroidery on Performance Polyester?
HIGHEST dye migration risk of any fabric type. Performance poly dyes are especially reactive. Never exceed 285F. Even 290F can trigger migration on dark performance jerseys. Tip: Start at 270F for 10 seconds. Only increase if adhesion test fails.
Wondering if Fauxbroidery is compatible with Performance Polyester? See the full compatibility analysis for Fauxbroidery Transfers on Performance Polyester
Order Fauxbroidery Transfers from Long Island DTF Printing
Wholesale fauxbroidery transfers starting at $0.06/sq inch. 24-hour standard turnaround. No minimums on most products.