Press Settings Reference
Fauxbroidery Transfers Press Settings for 100% Rayon
For Fauxbroidery Transfers on 100% Rayon: press at 270-295F for 10-15 seconds with light-medium pressure, cold peel. The dimensional puff layer in fauxbroidery transfers activates and expands within this temperature range on 100% Rayon. Use lighter pressure than standard DTF to avoid flattening the puff texture before it fully activates.
Quick Reference Settings
| Setting | Recommended Value |
|---|---|
| Temperature | 270-295F (132-146C) |
| Press Time | 10-15 seconds |
| Pressure | Light-Medium |
| Peel Method | Cold Peel (30-90 seconds) |
| Pre-Press Temp | 270-285F, 3-5 sec |
| Finish Press | 270-285F, 5-8 sec |
| Dye Migration Risk | moderate |
About 100% Rayon
100% Rayon (Viscose)
Common examples: 100% Viscose/Rayon fashion tops, Rayon challis blouses, Rayon jersey tees, Rayon shift dresses
Step-by-Step Pressing Process
- 1
Pre-press the fabric
Set your heat press to 270-285F. Press the substrate for 3-5 seconds without the transfer to remove moisture and flatten wrinkles. Gentle pre-press only. Rayon scorches easily. Keep pre-press under 5 seconds.
- 2
Position the transfer
Center the Fauxbroidery Transfers on the fabric in the correct placement location. For apparel, use a heat-resistant tape or alignment ruler to verify placement before pressing.
- 3
Apply heat and pressure
Press at 270-295F for 10-15 seconds with light-medium pressure. The puff layer will expand during pressing. Do not open the press early.
- 4
Peel the carrier film (cold peel)
Wait 30-90 seconds for the transfer to cool completely to room temperature before peeling. Peeling while still warm on a cold-peel film will lift the design. When in doubt, wait longer.
- 5
Finish press
Place a Teflon sheet or parchment paper over the peeled design. Re-press at 270-285F for 5-8 seconds with light pressure. Use Teflon sheet. Very light pressure. Rayon shows press marks easily.
Pre-Press Details
Gentle pre-press only. Rayon scorches easily. Keep pre-press under 5 seconds.
Finish Press Details
Use Teflon sheet. Very light pressure. Rayon shows press marks easily.
Fauxbroidery-Specific Notes for 100% Rayon
Fauxbroidery transfers include a raised puff layer that expands during pressing to replicate the dimensional look of embroidery. On 100% Rayon, press at 270-295F. Use light-medium pressure to allow the puff layer to expand outward rather than being compressed by excessive platen force. The puff texture is most visible on smooth, flat fabric surfaces.
Common Pitfalls on 100% Rayon
- Rayon is extremely heat-sensitive. Exceeding 295F can cause permanent scorching, fiber damage, and sheen changes.
- Too much pressure leaves permanent press marks — rayon does not recover from compression.
- Rayon can shrink under heat. Do not over-press.
- Some rayon dyes are reactive. Test on an inconspicuous area first.
Pro Tips for 100% Rayon
- Cold peel is safest for rayon. Let the transfer cool completely (60+ seconds) before peeling.
- If adhesion feels weak at 270F, increase time by 2-3 seconds rather than raising temperature.
- Use a pressing pillow inside the garment to prevent press marks and ensure even pressure.
- Rayon DTF transfers are achievable but require the most careful handling of any common fabric.
Frequently Asked Questions
What temperature should I use for Fauxbroidery on 100% Rayon?
Press at 270-295F (132-146C). Start at the lower end of the range and increase only if adhesion test fails.
How long should I press Fauxbroidery transfers on 100% Rayon?
Press for 10-15 seconds at light-medium pressure.
Hot peel or cold peel for Fauxbroidery on 100% Rayon?
Cold peel is required for 100% Rayon. Wait at least 30-60 seconds after pressing before peeling the carrier film.
What are the most common mistakes when pressing Fauxbroidery on 100% Rayon?
Rayon is extremely heat-sensitive. Exceeding 295F can cause permanent scorching, fiber damage, and sheen changes. Too much pressure leaves permanent press marks — rayon does not recover from compression. Tip: Cold peel is safest for rayon. Let the transfer cool completely (60+ seconds) before peeling.
Wondering if Fauxbroidery is compatible with 100% Rayon? See the full compatibility analysis for Fauxbroidery Transfers on 100% Rayon
Order Fauxbroidery Transfers from Long Island DTF Printing
Wholesale fauxbroidery transfers starting at $0.06/sq inch. 24-hour standard turnaround. No minimums on most products.